Custom manufacturing example · Black automotive rubber grommet/rubber wiring grommets

CUSTOM RUBBER & SILICONE MANUFACTURING

Black automotive rubber grommet/rubber wiring grommets

A custom component for your assembly.

Define the mating surfaces, dimensions and working conditions. ETOL manufactures the part to the agreed design and material.

Factory direct
Made to order
Drawing & sample support

Share the part, its application and your estimated quantity.

Customize the fit, material and finish

Vulcanization workshop illustration with green molding presses and blue collection bins

Material & hardness

Selected for the contact, temperature and movement

Color & finish

Define the visible surfaces and intended color

Shape & dimensions

Develop holes, lips and walls around the mating parts

Mounting & fit

Match the attachment and installation method

Product Overview

Black rubber wiring grommets can blend into an automotive harness and surrounding trim. This appearance may suit the assembly, but it can also make a partly lifted lip difficult to spot. The installation process should provide a clear view of the retaining area before the panel becomes crowded.

Custom dimensions and material options allow the grommet to follow the opening and cable route. Establish the panel groove using the finished wall thickness, including coatings. The cable passage should suit the jacket or harness wrapping that actually occupies it.

During fitting, check the grommet around the entire perimeter rather than judging only the visible front face. Secure the nearest harness supports and inspect again for sideways pull. If the part is hidden after trim installation, verify its seat at the appropriate earlier stage. Select the compound for the local heat and exposure conditions. During maintenance, distinguish a loose harness clip from a damaged grommet; both can alter the cable's position, but replacing the rubber does not restore a missing support.

Material options: Custom rubber compound and color, selected for the contact conditions and required geometry.
Hardness range: 30–90 Shore A for rubber. Assess the grade against this fit requirement: The installation process should provide a clear view of the retaining area before the panel becomes crowded.
Custom profile & fit: Establish the panel groove using the finished wall thickness, including coatings.
Assembly considerations: If the part is hidden after trim installation, verify its seat at the appropriate earlier stage.
Design check: During fitting, check the grommet around the entire perimeter rather than judging only the visible front face.

Photos illustrate structure or material only. The cable passage should suit the jacket or harness wrapping that actually occupies it. ETOL directly manufactures custom-shaped silicone and rubber parts to your requirements.

Choosing a material or hardness? Explore the selection guide →

FIND THE RIGHT FIT

Round Grommet Size Catalog

Choose a profile to compare part numbers and dimensions. Inch and metric sizes are listed in separate tables.

Type D Round Grommets in Inches

274 entries for Type D round through-hole grommets. Original fractions are retained, and exactly equivalent standard inch fractions replace decimal values where possible. Other values remain decimal inches.

Generated product visualization of a black rubber Type D grommet with two round flanges, a panel mounting groove and an open central bore. — Illustrative product rendering. Refer to the table for dimensions.

P/N	ID (C)	GD (A)	OD (D)	GW (B)	T (E)	Unit
RG2001	7/64	5/32	1/4	3/32	11/64	inch
RG2002	7/64	5/32	1/4	3/64	11/64	inch
RG2003	5/32	7/32	9/32	3/32	7/32	inch
RG2004	1/8	3/16	5/16	1/16	3/16	inch
RG2005	9/64	1/4	5/16	5/64	1/4	inch
RG2006	5/32	1/4	5/16	7/64	13/64	inch
RG2007	1/8	3/16	11/32	1/16	7/32	inch
RG2008	1/8	1/4	11/32	1/16	7/32	inch
RG2009	1/8	1/4	11/32	3/32	1/4	inch
RG2010	9/64	3/16	11/32	1/16	3/16	inch
RG2011	3/16	9/32	13/32	3/32	5/16	inch
RG2012	3/16	5/16	13/32	1/16	7/32	inch
RG2013	3/16	9/32	7/16	3/32	7/32	inch
RG2014	3/16	5/16	7/16	1/16	3/16	inch
RG2015	3/16	5/16	7/16	1/4	3/8	inch

Type D Round Through-Hole Grommets

866 entries for round panel openings. Compare the outside diameter, inside diameter, panel hole, panel thickness and overall thickness for the required fit.

P/N	OD	ID	GD	GW	T	Unit
RG6-2-4-1	6	2	4	1	3	mm
RG6-2-4-1.5	6	2	4	1.5	3.5	mm
RG6-2-4-2	6	2	4	2	4	mm
RG8-2-6-1	8	2	6	1	3.4	mm
RG8-2-6-1.5	8	2	6	1.5	3.9	mm
RG8-2-6-2	8	2	6	2	4.4	mm
RG8-3-6-1	8	3	6	1	3.4	mm
RG8-3-6-1.5	8	3	6	1.5	3.9	mm
RG8-3-6-2	8	3	6	2	4.4	mm
RG8-4-6-1	8	4	6	1	3.4	mm
RG8-4-6-1.5	8	4	6	1.5	3.9	mm
RG8-4-6-2	8	4	6	2	4.4	mm
RG10-3-7-1	10	3	7	1	4	mm
RG10-3-7-1.5	10	3	7	1.5	4.5	mm
RG10-3-7-2	10	3	7	2	5	mm

Type A Round Grommets

98 GRA sizes with a flanged sleeve profile. Compare the inside diameter, groove diameter and sleeve dimensions.

Generated product visualization of a black rubber Type A grommet with a flat upper flange, long sleeve and chamfered lower edge. — Illustrative product rendering. Refer to the table for dimensions.

P/N	ID	OD	GD	GW	T	Unit
GRA5000	2	8	5	7	8.5	mm
GRA5001	3	8	5	7	8.5	mm
GRA5002	3.5	9	6	8	9.5	mm
GRA5003	3.2	8.2	6	8	9	mm
GRA5004	3.5	11	6.8	8	10	mm
GRA5005	4	10	7	8	9.5	mm
GRA5006	4	11.5	7.3	8	10	mm
GRA5007	4.5	12	7.8	8	10	mm
GRA5008	4.5	11	8	8	9.5	mm
GRA5009	5.5	13	9	8	10	mm
GRA5010	5	12.5	8.3	8	10	mm
GRA5011	5	13	9	9	11	mm
GRA5012	6	14	10	9	11	mm
GRA5013	7	15	11	10	12	mm
GRA5014	7.5	16	12	10	12	mm

Type B Round Grommets

47 RGB sizes with a retaining lip below the mounting groove. Check the groove width and overall thickness for the panel assembly.

Generated product visualization of a black rubber Type B grommet with a flat upper flange, lower retaining lip and central bore. — Illustrative product rendering. Refer to the table for dimensions.

P/N	ID	OD	GD	GW	T	Unit
RGB6001	2	8.5	4.6	3	8	mm
RGB6002	2.5	9	5	3	7	mm
RGB6003	3	9.5	5.5	3	7	mm
RGB6004	3.5	10	6	4	8	mm
RGB6005	4	10.5	6.5	4	8	mm
RGB6006	4.5	11	7	4	8	mm
RGB6007	5	11.5	7.5	4	8	mm
RGB6008	5.5	12	8	4	8	mm
RGB6009	6	12.5	8.5	4	8	mm
RGB6010	6.2	13	9	5	9	mm
RGB6011	6.5	13.5	9.5	5	9	mm
RGB6012	7	14	10	5	9	mm
RGB6013	7.5	14.5	10.5	5	9	mm
RGB6014	8	15	11	5	9	mm
RGB6015	8.5	15.5	11.5	5	9	mm

Blind-Hole Round Grommets

39 BGA sizes with a closed central membrane. Match dimensions A through E to the section drawing and the panel opening.

Generated product visualization of a black rubber BGA blind-hole grommet with a recessed closed membrane and an outer panel groove. — Illustrative product rendering. Refer to the table for dimensions.

P/N	A	B	C	D	E	Unit
BGA1001	10	12	17	2.5	7.5	mm
BGA1002	14	16	21	2.5	9.5	mm
BGA1003	15	20	26	2	9	mm
BGA1004	18	22	28	2.5	9.5	mm
BGA1005	20	25	33	2.5	11	mm
BGA1006	22	27	34	1.6	9	mm
BGA1007	22	28	34	2.5	10	mm
BGA1008	25	30	40	3	10	mm
BGA1009	24	32	40	2.5	11	mm
BGA1010	30	35	45	2.5	10	mm
BGA1011	30	38	45	3	12	mm
BGA1012	32	40	47	3	10.5	mm
BGA1013	35	42	50	2.5	10.5	mm
BGA1014	36	47	53	3	10	mm
BGA1015	42	48	58	6	16	mm

Can't find the right size? Contact us for custom dimensions tailored to your requirements.

From part requirements to production

Define the part

Identify key dimensions, mating surfaces and quantity

Review material & tooling

Agree the compound and manufacturing approach

Evaluate the sample

Review the fit and agreed requirements in the assembly

Produce & inspect

Manufacture and check against the approved requirements

Review the intended assembly

Working conditions

Identify temperature, contact fluids and repeated movement.

Material and structure

Consider hardness together with wall thickness and support.

Installation

Check access, mating dimensions and the fitting sequence.

Ordering this custom component

Can the shape be adjusted to my mating parts?

Yes. Show the receiving opening, contact surfaces and clearance limits. We can review the dimensions and retaining features around the intended fit.

Which details should be agreed before tooling?

Agree the critical dimensions, material, hardness, visible surfaces and sample requirements. Explain how the part is installed and which interfaces control its function.

Can a sample help define the replacement?

A sample can help explain the structure. Compare it with the assembly because wear, swelling or compression may have changed its original dimensions.

How is the quotation for this part determined?

The material, part geometry, tooling, quantity and finishing affect the quotation. Include the intended batch size and delivery destination when describing your requirements.

DISCUSS THIS COMPONENT

Describe the part you need.

Share the fit, operating conditions and quantity with our manufacturing team.