Custom manufacturing example · Cable Rubber Oval Grommets Manufacturer

CUSTOM RUBBER & SILICONE MANUFACTURING

Cable Rubber Oval Grommets Manufacturer

A custom component for your assembly.

Define the mating surfaces, dimensions and working conditions. ETOL manufactures the part to the agreed design and material.

Factory direct
Made to order
Drawing & sample support

Share the part, its application and your estimated quantity.

Customize the fit, material and finish

Vulcanization workshop illustration with green molding presses and blue collection bins

Material & hardness

Selected for the contact, temperature and movement

Color & finish

Define the visible surfaces and intended color

Shape & dimensions

Develop holes, lips and walls around the mating parts

Mounting & fit

Match the attachment and installation method

Product Overview

Cable rubber oval grommets provide an elongated opening where several wires need to cross a panel edge. The useful passage is the inside opening remaining after the grommet is seated, not the full area of the bare cutout. This distinction matters when a cable bundle may change during assembly or later servicing.

Compare the current bundle with the largest approved wiring configuration. Allow for the position of the wires rather than assuming they will pack into a perfectly regular shape. A connector or protective sleeve may also need to pass through at installation. If it cannot, review the assembly sequence instead of forcing it through and dislodging the retaining flange.

Check both axes of the internal passage and the groove width against the cable arrangement and panel thickness. Increasing the long axis does not necessarily create enough clearance for a bulky connector on the short axis. Nearby components also need room for the outer flange, including on the hidden side of the panel.

ETOL can develop a custom profile when the approved wiring configuration does not suit a listed entry. Once the cables are routed, inspect the grommet for stretching and confirm that the bundle is not levering it against one curved end. During a wiring change, check the entry again before closing the enclosure. Keeping the cable route within the intended passage helps preserve edge protection without treating the rubber as spare space for an increasingly crowded bundle.

Material options: Custom rubber compound and color, selected for the contact conditions and required geometry.
Hardness range: 30–90 Shore A for rubber. Balance insertion flexibility with support around the opening. Allow for the position of the wires rather than assuming they will pack into a perfectly regular shape.
Custom profile & fit: Check both axes of the internal passage and the groove width against the cable arrangement and panel thickness.
Assembly considerations: The useful passage is the inside opening remaining after the grommet is seated, not the full area of the bare cutout.
Design check: Compare the current bundle with the largest approved wiring configuration.

Photos illustrate structure or material only. The useful passage is the inside opening remaining after the grommet is seated, not the full area of the bare cutout. ETOL directly manufactures custom-shaped silicone and rubber parts to your requirements.

Choosing a material or hardness? Explore the selection guide →

FIND THE RIGHT FIT

Oval Grommet Size Catalog

Choose a through-hole or blind-hole profile, then compare the dimensions for your panel and cable arrangement.

Through-Hole Oval Grommets

133 sizes with an open passage for cables. Match the outside dimensions, opening, panel hole, panel thickness and overall thickness. Dimensions are in millimeters (mm).

PRODUCT FORM

Representative profile. Refer to the table for available dimensions.

P/N	OD	ID	GD	GW	T
OG9001	29×49	20×40	23×43	4	8
OG9002	71.5×37.2	53.5×19.2	59.5×25.2	3.5	7.2
OG9003	112×43.5	98.5×30	101.5×33	3.5	7.2
OG9004	83×40	71×28	75×32	2	6
OG9005	39×19	32×12	35×15	2	5
OG9006	19.5×10	13.5×4	15.5×6	2	5
OG9007	14×24	8×18	10×20	1	4
OG9008	14×24	8×18	10×20	1.5	4.5
OG9009	14×24	8×18	10×20	2	5
OG9010	14×24	8×18	10×20	2.5	5.5
OG9011	14×24	8×18	10×20	3	6
OG9012	14×24	8×18	10×20	4	7
OG9013	14×29	8×23	10×25	1	4
OG9014	14×29	8×23	10×25	1.5	4.5
OG9015	14×29	8×23	10×25	2	5

Blind-Hole Oval Grommets

16 sizes with a closed oval profile. Compare the groove dimensions and panel thickness for the mounting fit. Dimensions are in millimeters (mm).

PRODUCT FORM

Representative profile. Refer to the table for available dimensions.

P/N	OD	ID	GD	GW	T
GBH2002	15×30	10×25	13×27	3	10
GBH2003	23×48	17×42	20×44	3	10
GBH2004	25×51	16×42	20×45	2	9
GBH2005	25×51	16×42	20×50	2	9
GBH2006	30×45	21×37	25×40	2	9
GBH2007	37×91	24×78	30×85	2	11
GBH2008	46×84	29×67	37×75	2	11
GBH2009	46×90	33×77	40×83	3	14
GBH2010	58×83	45×70	50×75	3	14
GBH2011	41×105	26×90	35×100	2.5	9.5
GBH2013	38×83	26×71	30×75	4	9
GBH2014	48×128	26×110	40×120	3	10
GBH2015	25×40	16×31	20×35	1.5	5.5
GBH2016	38×53.8	24×39.8	31×46.8	2.54	6.35
GBH2017	26×66	17×57	20×60	1	5

Can't find the right size? Contact us for custom dimensions tailored to your requirements.

From part requirements to production

Define the part

Identify key dimensions, mating surfaces and quantity

Review material & tooling

Agree the compound and manufacturing approach

Evaluate the sample

Review the fit and agreed requirements in the assembly

Produce & inspect

Manufacture and check against the approved requirements

Review the intended assembly

Working conditions

Identify temperature, contact fluids and repeated movement.

Material and structure

Consider hardness together with wall thickness and support.

Installation

Check access, mating dimensions and the fitting sequence.

Ordering this custom component

Can the shape be adjusted to my mating parts?

Yes. Show the receiving opening, contact surfaces and clearance limits. We can review the dimensions and retaining features around the intended fit.

Which details should be agreed before tooling?

Agree the critical dimensions, material, hardness, visible surfaces and sample requirements. Explain how the part is installed and which interfaces control its function.

Can a sample help define the replacement?

A sample can help explain the structure. Compare it with the assembly because wear, swelling or compression may have changed its original dimensions.

How is the quotation for this part determined?

The material, part geometry, tooling, quantity and finishing affect the quotation. Include the intended batch size and delivery destination when describing your requirements.

DISCUSS THIS COMPONENT

Describe the part you need.

Share the fit, operating conditions and quantity with our manufacturing team.